TP Link Network Card TL WN827N User Manual

TL-WN827N  
Wireless N USB Adapter  
Rev: 1.0.2  
1910010101  
 
FCC RF Radiation Exposure Statement  
This device has been tested for compliance with FCC RF Exposure (SAR) limits in the typical  
laptop computer configuration and this device can be used in desktop or laptop computers with  
side mounted PCMCIA slots. This device cannot be used with handheld PDAs (personal digital  
assistants). This device and its antenna must not be co-located or operated in conjunction with  
any other antenna or transmitter.  
CE Mark Warning  
This is a class B product. In a domestic environment, this product may cause radio interference, in  
which case the user may be required to take adequate measures.  
National restrictions  
This device is intended for home and office use in all EU countries (and other countries following  
the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:  
Country  
Restriction  
Reason/remark  
General authorization required for outdoor use and  
public service  
Bulgaria  
Outdoor use limited to 10 Military Radiolocation use. Refarming of the 2.4 GHz  
mW e.i.r.p. within the band band has been ongoing in recent years to allow current  
France  
2454-2483.5 MHz  
relaxed regulation. Full implementation planned 2012  
If used outside of own premises, general authorization is  
required  
Italy  
General authorization required for network and service  
supply(not for spectrum)  
Luxembourg  
None  
This subsection does not apply for the geographical area  
within a radius of 20 km from the centre of Ny-Ålesund  
Norway  
Implemented  
Russian Federation  
Only for indoor applications  
Note: Please don’t use the product outdoors in France.  
II  
 
CONTENTS  
III  
 
TL-WN827N Wireless N USB Adapter User Guide  
Package Contents  
The following items should be found in your package:  
¾
¾
¾
One TL-WN827N Wireless N USB Adapter  
One USB extension cable (for 100 meters)  
One Resource CD for TL-WN827N Wireless N USB Adapter, including:  
Drivers and Utility  
User Guide  
Other Helpful Information  
)
Note:  
Make sure that the package contains the above items. If any of the listed items are damaged or  
missing, please contact with your distributor.  
- 1 -  
 
 
TL-WN827N Wireless N USB Adapter User Guide  
Chapter 1 Introduction  
1.1 Product Overview  
Thank you for choosing the TL-WN827N Wireless N USB Adapter.  
The adapter is a draft 802.11n client device; it is designed to provide a high-speed and unrivaled  
wireless performance for your computer. With a faster wireless connection, you can get a better  
Internet experience, such as downloading, gaming, video streaming and so on.  
The TL-WN827N Wireless N USB Adapter complies with IEEE 802.11n (Draft 2.0), IEEE 802.11g,  
and IEEE 802.11b standards. It can interoperate with all the 802.11n/g/b devices. With the  
802.11n technology, higher throughput improvements using MIMO (multiple input, multiple output  
antennas), the TL-WN827N’s auto-sensing capability allows high packet transfer rate of up to  
300Mbps for maximum throughput.  
Additionally, the TL-WN827N adapter has good capability on anti-jamming and supports WEP,  
TKIP, AESWPA and WPA2 encryption to prevent outside intrusion and protect your personal  
information from being exposed.  
The adapter is easy to install and manage. The TL-WN827N supports WPS function, which can  
help you create a wireless connection immediately. Quick Setup Wizard is supported and detailed  
instructions are provided step by step in this user guide.  
Featuring high performance transmission rates, simple installation and adaptability, as well as  
strong security, the TL-WN827N Wireless N USB Adapter is the perfect solution for small office  
and home needs.  
1.2 Main Features  
¾
¾
Complies with IEEE802.11 Draft N standards  
Supports WPA data security, IEEE802.1x authentication, TKIP/AES encryption, 64/128-bit  
WEP encryption  
¾
¾
¾
¾
¾
¾
¾
Supports wireless LAN data transfer rate of up to 300Mbps  
Provides USB interface  
Supports Ad-Hoc and Infrastructure modes  
Supports roaming between access points when configured in Infrastructure mode  
Eases configuration and provides monitoring information  
Supports Windows 2000, XP, Vista  
Internal Antenna  
- 2 -  
 
 
TL-WN827N Wireless N USB Adapter User Guide  
1.3 LED Status  
The LED on the top of this card indicates Link/Act status. It blinks at green light when sending and  
receiving data.  
Chapter 2 Installation Guide  
2.1 Hardware Installation  
1. Connect one end of the USB cable to the Adapter.  
2. Connect the other end of the USB cable to the USB port on your computer. Because the  
Adapter gets its power from the host, there is no external power supply. The LED should light  
up when the Adapter is plugged in and the PC is on.  
Note:  
)
The Adapter can also be plugged into the USB port on your computer directly.  
2.2 Software Installation  
2.2.1 Overview  
The Adapter’s Setup Wizard will guide you through the installation of the Utility and drivers for  
Windows 2000, XP and Vista.  
Before you install the software, please plug the adapter into your PC. After that, you will be  
prompted “Found New Hardware Wizard”, click the Cancel button, and run the Setup Wizard  
program on the CD-ROM.  
The Setup steps for Windows 2000, XP and Vista are very similar, so the following installation  
guide takes Windows XP for example.  
2.2.2 Installation Guide  
1. Insert the Resource CD into your CD-ROM drive, click the Start button and choose Run. In  
the field that appears, enter F:\TL-WN827N\Setup.exe (if “F” is the letter of your CD-ROM  
drive), Figure 2-1 should then appear.  
- 3 -  
 
 
TL-WN827N Wireless N USB Adapter User Guide  
Figure 2-1 Preparing Setup  
2. To continue, the following Figure 2-2 will appear within seconds. You can select the  
configuration tool here.  
Figure 2-2 Setup Type  
I. If you want to install the TL-WN827N Wireless Utility, please select the TP-LINK  
Configuration Tool and click Next.  
- 4 -